|
CP16 Pentium M cPCI Single Board Computer
Trenton Technology's CP16 uses the Intel® Pentium®
M processor to provide maximum processing and thermal performance.
The processor's micro-architecture and power management features like
Enhanced Intel SpeedStep® technology make this possible.
PICMG® compliance and features like a local storage
option and the ability to turn off the CompactPCI® bus enable the
CP16 to excel in a wide variety of either CompactPCI system board
or server blade computing applications.
Key features designed into the CP16 include a front access PMC slot,
local storage options, dual Gigabit Ethernet ports and support for up to 2GB of
DDR220/266 memory.
A rear transition module, RTM25, is available with
or without dual Ultra320 SCSI interfaces and provides rear access
to the SBC's I/O ports and status LEDs.
Key features of the CP16 include:
- Intel® Pentium® M processor with the Intel® E7501 chipset
- PICMG® 2.16 Packet Switching Backplane and PICMG® 2.1 (Hot Swap) support
- Optional PICMG® 2.9 (IPMI)
- Ability to turn off the CompactPCI® bus
- Optional plug-in CompactFlash™ or Microdrive® storage
- Dual Gigabit Ethernet
- Supports up to 2GB of DDR200/266 plug-in memory modules
- Enhanced ATI® video
- Optional Rear Transition Module available with or without Dual Ultra320 SCSI
Form Factor
The CP16 is a single-slot module (4HP width) with a 6U height and is
fully compliant with the CompactPCI® Core Specification: PICMG® 2.0, R3.0.
Chip Set
The CP16 uses the Intel® E7501 chipset which provides support for DDR200/266
memory with ECC and a high-speed Hub Link 2.0 interface. Intel® Pentium® M processors support a
400MHz FSB.
CompactPCI Bus
The CP16 provides direct support for up to seven expansion CompactPCI slots
at 32-Bit/33MHz and up to four expansion slots at 64-Bit/66MHz. Each slot provides support for
PCI Bus mastering. The CompactPCI bus can be turned off via the CP16’s CompactPCI bus switches
for server blade applications.
PMC Option Card Slot
PMC 32/64-bit, 33/66MHz option cards are supported by the CP16 via an
access slot in the SBC’s front panel.
Bus Speed
- CompactPCI® Bus 32-bit/33MHz, 32-bit/66MHz, 64-bit/33MHz, 64-bit/66MHz
- PCI-X Local Bus 64-bit/100MHz
- PCI Local Bus 32-bit/33Mhz & 64-bit/100MHz
- Hub Link 2.0* 1GB/s
- System/FSB 400MHz
* Hub Link D is routed to J4 for high-speed interface usage on the optional
RTM25
Packet Switching Backplane Support
Channel B of each Ethernet controller provides a redundant 10/100/1000Base-T
Ethernet interface via connector J3 to the CompactPCI backplane. This allows Ethernet
communication and control between the CP16 and other boards in the CompactPCI chassis. The
interface implementation is fully compatible with the PICMG® 2.16, R1.0 specification.
Hot Swap & Optional OPMI Support
The CP16 supports the Hot Swap (PICMG® 2.1, R2.0) and Hot Swap Infrastructure
(PICMG® 2.12, R2.0) specifications. Optional support is available for the Intelligent Platform
Management Interface (IPMI, PICMG® 2.9, R1.0) specification.
Local Storage Option
A Compact Media Daughter Card (CMDC) plugs into connector P11A on the CP16
and provides support for either a CompactFlash™ or Microdrive® storage device. In server
blade applications this option is useful for storing the operating system and application.
BIOS (Flash)
The CP16’s BIOS is AMIBIOS8® with IPMI extensions. The flash BIOS resides
in the 82802 Firmware Hub (FWH). Some of the key features of the BIOS are:
- Boot from network, USB mass storage devices, IDE, ATAPI or SCSI
- Serial port console redirection to support headless operation
- IPMI v1.5 Baseboard Management Controller (BMC) support
- Intel SpeedStep® support
- Optional CompactPCI bus support
- Supports either system board or blade card applications
Cache Memory (L2)
Intel® Pentium® M processors 1.8GHz and above have a 2MB on-die, Level 2 (L2)
cache memory with Advanced Transfer Cache architecture. Processors below 1.8GHz have a L2 cache
of 1MB. The processors also have a Level 1 (L1) 32K instruction and data cache.
DDR200/266 Memory
The CP16 provides a single channel DDR memory interface terminating at a
DIMM socket. The memory interface supports up to 2GB of memory and has an interface bandwidth
of 1600MB/s. The SBC accepts a single ECC, registered PC1600 or PC2100 DIMM.
PCI-X and PCI Local Bus Interfaces
The CP16’s on-board PCI-X bus, which runs at 64-bit/100MHz, supports the
SBC’s dual Ethernet controllers to provide full-speed Gigabit functionality to the module’s LAN
ports and backplane connector J3. Primary PCI Interface: The Primary PCI interface runs at
32-bit/33MHz and supports the on-board video interface. Secondary PCI Interfaces: Two secondary
PCI interfaces are 32/64-bit, operating at 33/66MHz and drive the local PMC slot and
CompactPCI passive backplanes. The CP16 features CompactPCI bus switches for turning off the bus
in applications not requiring CompactPCI bus support.
Dual Ethernet Interfaces - 10/100/1000BASE-T
An internal 64-bit/100MHz PCI-X bus connects to the CP16’s Ethernet controllers, ensuring
full-speed Gigabit Ethernet in applications using 1000Base-T Ethernet communications. Channel A
on each controller supports 10/100/1000Base-T Ethernet connectivity to the RJ-45 connectors
located on the CP16’s front panel. Channel B on each controller enables the SBC’s Packet
Switching Backplane capability.
Rear Transition Module (optional)
The RTM25 is available for use in CP16 applications where rear access I/O
panel connectors are required. The RTM25 is not required for the CP16 to function. The RTM25’s
optional Ultra320 SCSI interfaces utilize the high-speed, 1GB/s Hub Link 2.0 interface from
the CP16’s E7501 Memory Controller Hub.
Universal Serial Bus (USB)
A total of four (4) USB ports are available on the CP16. USB ports 0 and 1
are located on the CP16’s front panel and USB ports 2 and 3 are available at connector J5. The
CP16’s chipset supports USB revision 1.1
EIDE ULTRA ATA/100 Interfaces(Dual)
Dual high-performance PCI EIDE interfaces are capable of supporting up to
two IDE disk drives each in a master/slave configuration. The interfaces support Ultra ATA/100
with synchronous ATA mode transfers up to 100MB per second. The interfaces are routed through
backplane connector J5. Dual EIDE connectors are available on the optional RTM25 rear
transition module.
Ultra XGA Video Interface
The ATI® M6-C16H video controller enables 2D/3D video acceleration and provides
16MB of integrated video DDR memory. The video controller supports pixel resolutions up to
1600 x 1200 (UXGA). Software drivers are available for most popular operating systems.
Serial Interface
The Super I/O controller supports two full-function serial ports with
independently programmable baud rates. The controller has two high-speed, NS16C550 compatible,
UARTs with Send/Receive 16-Byte FIFOs. The IRQ for each serial port has BIOS selectable
addressing. Serial port 1 is located on the CP16’s front panel and serial port 2 is routed to
the RTM25 via backplane connector J5. Serial devices may be attached to the front panel and to the
RTM25.
Floppy Drive Interface
The CP16 supports up to two floppy disk drives. Drives can be 360K to 2.88MB,
in any combination. The floppy drive interface is routed to the RTM25 via backplane connector
J5.
Keyboard & Mouse Interfaces
The keyboard and mouse interfaces are routed to the RTM25 via backplane
connector J5. A mini DIN connector located on the RTM25 provides an external interface for a
PS/2 mouse and keyboard. A "Y" adapter plugged into the mini DIN connector allows the PS/2
mouse and keyboard to share the same port. Internal PS/2 mouse and keyboard headers are
also available on the RTM25. A self-resetting fuse on the RTM25 protects the +5V line of the
keyboard and the mouse.
Power Requirements
Typical Values
- 1.6GHz* +5V@6.20A +12V@0.20A +3.3V@3.99A
- 1.6GHz** +5V@4.00A +12V@0.20A +3.3V@5.80A
- -12V @ less than 100mA
*5V(I/O) configured backplane
**3.3V(I/O) configured backplane
Battery
Built-in lithium battery for data retention of CMOS memory.
Temperature / Environment
- Operating Temperature 0° to 55° C. with 350 LFM of airflow
- Storage Temperature -20° to 70° C.
- Humidity 5% to 90% non-condensing
- Cooling Solution Passive Heat Sink
Agency Approvals & Industry Compliance
- Designed for UL 1950, CAN/CSA C22.22 Number 950-95, EN55022:1994/A2:1997,
CLASS A, EN55024, EN6100-6-2:1999, EN61000-3-2:2001
- The CP16 is designed for NEBS/ETSI compliance
Mean Time Between Failures (MTBF)
164,040 POH (Power-On Hours) at 40 °C., per Bellcore
Ordering Information
For further details of these and other Trenton Technology products, please
see the Trenton Technology web pages on this site or contact us via our
Contacts page.
|
