Extreme Engineering Solutions Inc.

XPort1011

Multi-Protocol Four Port Serial PCI Card Based on the MPC8260 PowerQUICC II™ Series

The Extreme Engineering Systems XPort1011 is an intelligent communications controller targeting high performance yet low cost applications. XPort1011 combines a wide array of supported serial protocols, a broad range of serial interface standards, and a flexible I/O routing structure, to pack maximum flexibility into an industry standard PCI card.

PowerQUICC II™

Powered by the MPC8250 (PowerQUICC II™), the XPort1011 implements four serial communication ports providing a EIA-530-A compliant signal set. Supporting HDLC/SDLC, UART, Transparent and BISYNC modes, with NRZ, NRZI, FM0, FM1, Manchester and Differential Manchester encoding. Coupled with software configurable support for RS-232, RS-422, RS-423, RS-485 and MIL-STD-188-114, XPort1011 provides maximum flexibility for your application.

Software Configurable

For solutions which require low cost but high performance, the Extreme Engineering Solutions XPort1011 is also available in configurations which provide a 7-wire signal set. This configuration implements four serial communication ports providing TXD, RXD, TXC, RXC, RTS, CTS and DCD flow control, with software configurable support for RS-232, RS-422, RS-423, and RS-485.

Low Power

As a system designer, XPort1011 will help drive both cost and power consumption out your system. Because the PCI bridge is integrated on chip, XPort1011 draws up to 40% less power, and costs up to 30% less than conventional designs based on other processors.

Processor

• MPC8250 PowerQUICC II
• Embedded PowerPC G2 Core
• 133-300MHz
• 280 Dhrystones at 200MHz
• 66MHz 60x Bus
• 16KB Instruction and Data Caches
• 32KB internal SRAM
• Integrated MMU
• Integrated Floating Point Unit
• Core Disabled Mode supported

Memory

• 32-256MB SDRAM
• SDRAM doubles as 8MB of buffer storage in Core Disabled Mode
• 4-16MB Surface Mount Flash
• 512KB Socketed Flash
• KB Serial EEPROM

Serial Communication Controller

• HDLC, UART, Transparent and BISYNC modes
• DPLL supporting NRZ, NRZI, FM0, FM1, Manchester and Differential Manchester
• Independent BRG’s for each SCC transmitter and receiver
• Optional External Custom Oscillators

Serial Interface (Standard)

• Software Configurable Drivers for RS-232, RS-422, RS-423, RS-485, and MIL-STD-188-114 Balanced/Unbalanced Type 1 and 2 Modes
• 10Mbps Max Synchronous
• 4Mbps Max Asynchronous
• EIA-530-A DTE/DCE Cable Selectable

Serial Interface (7 Wire)

• Software Configurable Drivers for RS-232, RS-422, RS-423, and RS-485
• 10Mbps Max Synchronous
• 4Mbps Max Asynchronous
• 7 Wire Interface
• DTE/DCE Mode Cable Selectable

Software

• VxWorks BSP
• SCC and SMC
• Linux LSP

Physical

• PCI Form Factor

Power Requirements (Typical)

• +3.3V 0.60A 1.98W
• +5.0V 0.35A 1.75W
• +12.0V 0.012A 0.15W
• -12.0V 0.012A 0.15W

Operating Temperature

• 0 to +55C ambient, at board

Humidity

• 0% to 85%

Storage Temperature

• -40 to +70C

Please visit the Extreme Engineering Solutions web site for full details of the complete range of products and services.

Please contact Sarsen Technology on +44 1672 511166 for technical support, pricing and lead time information on the full range of Extreme Engineering Solutions products.